2x 200G OSFP GFR4 with dual CDR 2 km, λ1272-1332 nm, Mini-LC, Singlemode

Universal OSFP Transceiver
Use FLEXBOX in combination with FLEXSOX to configure to almost any vendor
For 200GBASE-GFR4 Ethernet links
Integrated Clock-Data-Recovery (CDR)
PAM4 modulated signal
Triple rate operation: the ability to operate at 53.125Gbps (PAM4), 25.78125Gbps (NRZ) and 10.3125Gbps (NRZ) per channel. G.652 SM
Supported Data Rates: 2x 41.25 Gbit/s - 2x 212.5 Gbit/s
Up to 2 km via Singlemode OS2
2x Mini-LC Connector
Specs
  • int. Mux
  • 2 km
  • 2x 212.5 G
  • Mini-LC
Protocols
  • 200G ETH
  • 400G ETH
Part number
O.162HG2.2.CK
Availability
On request
You can create a quote from your cart.
Just go to cart and click CREATE QUOTE.

Specification

Form Factor OSFP
Connector / Polish 2x Mini-LC PC
Interface Singlemode
Type 2x GFR4
Distance 2 km
Temperature Range 0°C - 70°C
Lane Count 8x (Tx/Rx)
Bandwidth 2x 41.25 Gbit/s - 2x 212.5 Gbit/s
Bandwith Per Lane 10.31 Gbit/s - 53.13 Gbit/s
Digital Diagnostic Management (DDM) Yes, externally calibrated
Power Consumption 13 W
CDR TX and RX
SGMII No
Inbuilt FEC No
Powerbudget (dB) 5 dB
Transmit min/max per lane -3 dBm / 2.5 dBm
Receiver min/max per lane -8 dBm / 2.5 dBm (overload)
Wavelength TX (Typical) 1271.5 nm, 1271.5 nm, 1291.5 nm, 1291.5 nm, 1311.5 nm, 1311.5 nm, 1331.5 nm, 1331.5 nm
Wavelength RX (Typical) 1271.5 nm, 1271.5 nm, 1291.5 nm, 1291.5 nm, 1311.5 nm, 1311.5 nm, 1331.5 nm, 1331.5 nm
Laser EML
Receiver Type PIN
Modulation PAM4
Extinction Ratio 3.5 dB
Supported Protocols 400G Ethernet, 200G Ethernet

Configure Transceiver Using Your FLEXSOX

It's that easy to use
1. Slide-In
2. Insert A Transceiver
  • Insert a Universal Transceiver into the corresponding slot
3. Select And Configure
  • Choose vendor and compatibility
  • Press play
  • Configuration only takes a few seconds
4. Use With Device
  • Use the transceiver in your device. That's it!
  • Need it for another device? - Re-configure it again and again

Compatibility

All trademarks, registered companies & references cited are the sole property of their respective company and are used solely to assist in the identification of products.

  • MSA Standard compatible
Your vendor / compatibility is missing?

What customers say

Spending a few minutes of my time, first and foremost expressing how much I’m impressed by your friendliness, is the least I can do. Friendliness was followed by super-fast order processing and delivery. In a few words, unboxing and using your Flexbox is an utterly awesome experience. As in brilliant. Also saving us loads of time ordering optics. In addition to all of this – you deliver particular good build quality, too. You’ve got me impressed, thank you!
Mark van den Berg CTO - Icera Networks
The FLEXBOX allows us to use 100MBit/s to multi-gigabit transceivers in our product for a wide range of customer needs. We can not solve them without this magic box!
Klaus Degner Managing Director, Allegro Packets GmbH
Our engineers spend a lot of time in data centers connecting switches and routers from different vendors. With the FLEXOPTIX service not only their task gets easier, also the back office doesn't have to have a broad range of optics from different vendors in stock anymore. The days that an engineer stand next to a router with an optic from the wrong vendor are over. With the FLEXOPTIX FLEXBOX the engineer simply reconfigures the optic, and that’s that. As an added benefit with the FLEXBOX there is no need to connect a new cross-connect to a device to see if it is connected on the other side. The measurement option that comes with the FLEXBOX are very handy!
Thomas Verschuren Technical Consultant, IP Visie Networking B.V.
Using FLEXBOX and FLEXOPTIX transceivers mean for us Flexibility. We don’t use so much transceivers but we work with different brands each day. With a small amount in stock we can configure them with the right specifications for each use. Assuring it will perfectly fit the requirements of our equipments and costs are also reduced considerably. Setting up either the FLEXBOX and a transceiver on a computer or through the mobile app is just easy as 1,2,3. It tooks us less than 15 minutes between unboxing and using a transceiver. We really appreciate the mobile option so we can have the FLEXBOX in one hand, a transceiver in the other one and the phone with the app in the pocket for programming on the field. Thanks FLEXOPTIX for this really useful tool and for extending supported vendors in the future.
Christophe Mulkers CEO/CTO, Oufti Connections
More