ArubaOS ermöglicht den Einsatz von non HPE Transceivers & DACs (Software Version: 16.02)

Folgenden SW-Version benötigen die Geräte SW-Version > 16.02.000x:
2530 Starting YA.16.02.xxxx
2920 Starting WB.16.02.xxxx
2930F Starting WC.16.02.xxxx

Ehemalige / end-of-life Switches der Serien 3500 / 3500yl, 3800 und 5406zl / 5412zl mit V1 und/ order V2 Modulen unterstützen den Befehl nicht.

Wir freuen uns, wenn Ihr Eure Erfahrungen mit FLEXOPTIX Transceivern in HP / Aruba Geräten mit uns teilt. Schreibt uns einfach eine kurze E-Mail an: support@flexoptix.net.
Flexoptix erreichte Anfang des Jahres eine E-Mail von einem unserer Kunden (vielen Dank dafür). Der E-Mail waren folgende Informationen zu entnehmen:New enterprise features*: Allow third-party transceivers
Zu Deutsch: Neues Geschäftskunden Feature*: Unterstützung von Dritthersteller Optiken
Diese Aussage war auf ein kommendes SW-Release bezogen und vorerst leider nur eine Vorankündigung.Im Juli 2016 startete der Rollout der neuen SW-Version 16.02. Mit ihr ebenfalls die Möglichkeit "unsupported transceiver" oder besser gesagt alle Transceiver in den HPE/Aruba Geräten einsetzen zu können. Dies testeten wir direkt mit unseren Kunden an einem Aruba 2920 Series. In beiden Geräten konnten FLEXOPTIX Transceiver wie auch DACs ohne Probleme zum Laufen gebracht werden.
Warum arbeiten Aruba und Hewlett Packard an einem HPE ArubaOS für HP Switche?
Ganz einfach: Aruba Networks wurde 2016 von Hewlett Packard Networks gekauft und vertreibt unter der Marke Aruba nun sämtliche Netzwerkkomponenten.
Was bedeutet dies für mich als HP Nutzer? Mit dem neuen SW-Release können FLEXOPTIX Transceiver in HP ProCurve / Aruba Geräten eingesetzt werden. Hierzu wird bei uns im Shop die Kompatibilität "Aruba Network (ex. HP Networks) SW > 16.02" zur Verfügung gestellt. Es muss lediglich das Feature, wie unten beschrieben, aktiviert werden.
Das Feature kann auf den unterstützten Switchen mit Hilfe des CLI aktiviert werden. Die benötigten Schritte für Geräte mit dem HPE ArubaOS SW-Version > 16.02 sind hier kurz erläutert.

Bitte folgende Kommandos vor dem Stecken des Transceivers eingeben:
# config
# allow-unsupported-transceiver
DDM Informationen lassen sich wie folgt anzeigen:
# show interface transceiver detail
Detaillierte Transceiver Informationen werden über diesen Befehl abgerufen:
# show tech transceiver

Ein FLEXOPTIX Transceiver wird mit folgenden Eigenschaften angezeigt:
# show interface transceiver detail
Transceiver in A1*
   Interface Index    : 49
   Type               : SFP+SR
   Model              :   ??
   Connector Type     : LC
   Wavelength         : 850nm
   Transfer Distance  : 80m (50um), 20m (62.5um), 300m (50um OM3),
   Diagnostic Support : DOM
   Serial Number      : unsupported
  
Status
   Temperature : 55.375C
   Voltage     : 3.2902V
   Tx Bias     : 5.782mA
   Tx Power    : 0.5198mW, -2.842dBm
   Rx Power    : 0.4740mW, -3.242dBm
  
  Time Stamp    : Mon Aug 15 13:24:15 2016
* third-party transceiver
Ein Original HP J9150A wird folgendermaßen angezeigt:
# show interface transceiver detail
Transceiver in A2
   Interface Index    : 50
   Type               : SFP+SR
   Model              : J9150A
   Connector Type     : LC
   Wavelength         : 850nm
   Transfer Distance  : 80m (50um), 30m (62.5um), 300m (50um OM3),
   Diagnostic Support : DOM
   Serial Number      : CN63G625CT
  
Status
   Temperature : 45.628C
   Voltage     : 3.3024V
   Tx Bias     : 5.500mA
   Tx Power    : 0.6340mW, -1.979dBm
   Rx Power    : 0.5435mW, -2.648dBm
  
  Time Stamp    : Mon Aug 15 13:24:15 2016
 

Aus dem Dokument "HPE ArubaOS-Switch Management and Configuration Guide K/KA/KB.16.02"

Allow unsupported transceivers This feature enables and disables the use of non-HPE Aruba transceivers on HPE Aruba switches. Description The Allow Unsupported Transceiver feature allows the user to try a transceiver part (including DAC cables) without the switch attempting to authenticate it as a genuine HPE Aruba part. There is no guarantee that all third-party transceivers will work: typically the ones that work are industry-standard types as identified by the MSA standards body. Those parts that do not comply will most likely still not be enabled. HPE fully backs only HPE Aruba supported transceivers (listed in the switch QuickSpecs under Accessories); support efforts will be honored. Support efforts may require the customer to replace any non-HPE Aruba transceiver/DAC with an equivalent supported HPE Aruba branded transceiver/DAC.
Transceiver technologies enabled by this feature
FP-LX LC
SFP-LH LC
SFP-LX LC
SFP-SX LC
1000BX-D SFP-LC
1000BX-U SFP-LC
1S000Base-T
100-FX SFP-LC
100-BX-D SFP-LC
100-BX-U SFP-LC
10-GbE SFP+ SR
10-GbE SFP+ LR
10-GbE SFP+ LRM(1)
10-GbE SFP+ ER
10-GbE SFP+ 1m Direct Attach Cable
10-GbE SFP+ 3m Direct Attach Cable
10-GbE SFP+ 5m Direct Attach Cable(1)
10-GbE SFP+ 7m Direct Attach Cable(1)
QSFP+ SR4
QSFP+ LR4
QSFP+ eSR4
QSFP+ 1m Direct Attach
QSFP+ 3m Direct Attach
QSFP+ 5m Direct Attach
(1) May not be enabled in certain switch platforms that do not support this technology.
Allow unsupported transceivers
  1. Configure unsupported transceivers by issuing the following CLI command (see “CLI command” (page 95)):
    allow-unsupported-transceiver [confirm]
    The system displays a disclaimer message and requires a Y confirmation (unless the confirm option is specified).
  2. Do one of the following:
    - If any non-HPE Aruba transceivers are present in the switch before executing the command and you want to enable them, remove and reinsert them. If you do not do so, the transceivers will not be enabled.
    - If any non-HPE Aruba transceivers are not present in the switch and you want to enable them, insert them into the switch.
  3. (Optional) Verify that non-HPE transceivers are now allowed:
    show running-config
    If non-HPE Aruba transceivers are now allowed, the output from this command includes the line
    allow-unsupported-transceiver.
    For a complete description of the show config command, see the HPE ArubaOS-Switch Management and Configuration Guide (version 16.02 or later) for your switch series found at www.hpe.com/networking/support
  4. (Optional) List the enabled transceivers:
    show tech transceivers
    The output from this command is similar to the following:
    Transceiver Technical Information:
    Port # | Type | Prod # | Serial # | Part #
    --------+-----------+------------+------------------+----------
    A21 | 1000SX | J4858C | 3CA404J4BK | 1990-3662
    H8 *| 1000SX | ??         | unsupported |
    J8     | ??           | ??         | unsupported |
    * Indicates an unsupported transceiver.

Eine Antwort hinterlassen

Deine E-Mailadresse wird nicht veröffentlicht.
* Erforderliches Feld
Deine Daten werden gesammelt und verarbeitet gemäß unserer Datenschutzbestimmungen.